Conveyors

The Pax conveyor is specifically designed for on-bolster, under-die part and scrap removal. The "low-profile" design enables it to fit where many conveyors will not. Designed by our own tool & die craftsmen, the conveyor is built to survive the rough metal stamping environment. Features: Easy Installation - Quick Setup 2 1/2" Clearance Needed Low-Profile Rugged Woven Polyester PVC Belt Quick Belt Change Flared Tray Sides Standard 115 VAC Electrical Connection Drive Options: Inverted Drive Right Angle Drive Extended Top Drive< Other Available Options: Stop Belt Sensor Wiper Flush Mount Tension End 480 / 3 Phase Motor Variable Speed Motor Adjustable Support Stands Grease Gun Special Length Conveyors

U.S. Patents 5,904,240 & 6,186,318

Clearance

Only 2 1/2" of clearance is needed between the die and bolster for installation.

Low Profile

Once installed under the die, there is only 3/8" from the bolster to the top of the belt.

Woven Polyester Belt and Flared Side Trays

A rugged, woven polyester PVC belt rides on a strip of polyethylene to reduce friction. The belt is connected with stainless steel lacing and pin, and can be changed in less than five minutes. It can also be reversed to extend belt life.

Belt edges are covered by flared sides of the tray preventing scrap from working under the belt. The flared edges also assist in guiding material onto the belt.

Inverted Drive

The optional Inverted Drive may be required in applications where space limitations are present and where there is a need to drive the belt toward the conveyor motor end. This configuration may be arranged to move material toward or away from the motor.

Right Angle Drive

Like the Inverted Drive option, the Right Angle Drive configuration may also be required in applications where space limitations are present, and where there is a need to drive the belt toward the conveyor drive end.

This configuration may also be arranged to move material away from the motor.

Extended Top Drive

The optional Extended Top Drive may be required in applications where space limitations are present and where there is a need to drive the belt toward the conveyor motor end.

This configuration may be arranged to move material toward the motor with or without a flush mount tension end or away from the motor.

Please specify before ordering.

Stopped Belt Sensor

The optional Stopped Belt Sensor connects to the press control's die protection circuit. The sensor is designed to stop the press in an event that the belt is stopped.

Optional Wiper

The optional Wiper is self-adjusting and may be required in applications where there is a possibility of small slugs adhering to the belt. The wiper greatly reduces the chance of small slugs entering between the belt and tray and causing additional problems.

This option is available for both the tension end and drive end of the conveyor.

Flush Mount Tension End

The OPTIONAL Flush Mount Tension End may be required in applications that do not allow the conveyor to be inserted completely through the die. It is also well suited for removing parts and scrap off the end of dies. This option requires the use of either an inverted or right angle drive (belt travel towards drive end). These drive configurations include the self-adjusting wiper. Please note that the overall height of Flush Mount Tension End is reduced to 2".

View Dimensions

Adjustable Support Stands

Available in three sizes

• 16" - 24"
• 24" - 36"
• 36" - 55"

Specifications & Dimensions

Model Number Example:

1. Type (A = * Top Drive, B = Inverted Drive, Belt Driven Toward Motor, C = Inverted Drive, Belt Driven Away From Motor, D = Special, E = Right Angle Drive, Belt Driven Toward Motor, F = Right Angle Drive, Belt Driven Away From Motor, G = Extended Top Drive, Belt Driven Toward Motor, H = Extended Top Drive, Belt Driven Away From Motor)
2. Width (04 = Four - Inch Conveyor Width)
3. Length (06 = Six - Foot Exposed Belt Length)
4. Sensor (S = Sensor, N = No Sensor*)
5. Drive Hand (L = Left-Hand Drive*, R = Right-Hand Drive)
6. Belt Speed (040 = 40 F.P.M)**

*Standard conveyor configuration

** Other belt speeds available: 29, 34, 46, 54, 59, 69, 80, 92, 108 F.P.M.

Note: Not all belt speeds are available for all conveyor models.

Conveyors are available with standard left-hand chain drive and motor assembly or an optional right-hand chain drive and motor.

Conveyors are provided in widths from 4 to 11 inches, in one inch increments and 12 to 20 inches, in two inch increments.

Standard lengths range from 4 feet to 8 feet, in one-foot increments, measured over the length of the exposed belt.
(For conveyors longer than 8 feet or configurations other than standard, please contact the factory.)

View Dimensions

Major Tax Incentive For New Equipment Orders

Request Literature

Pax Products | Pre-Pressurized Lube | V-Series Lube | Conveyors | Die Doors

Home | About | Inventory | Lines | Docs | Surplus | Tax | Leasing | Search | Location | Contact