|
 |
DX/EV - High Speed Performance
Designed primarily for high speed applications, the computer-controlled DX/EV offers continuous
speed and accuracy up to 800 strokes-per-minute.
Material is fed through rolls made of hardened steel with permanently sealed and lubricated bearings. This reduces maintenance problems caused by dust and dirt contamination.
The resolver-based, AC brushless servo motor is mounted to the underside of the feed making it compact and easy to mount to the front, back or either side of a press. |
|
|
|
|
 |
AC brushless servo drive motor |
|
Hardened precision ground steel feed rolls |
|
Upper and lower feed rolls driven through a toothed belt |
|
Upper roll pilot release precisely controlled by a high speed cylinder |
|
"End of stock" proximity switch |
|
Fully computerized controller with:
· User-friendly keypad.
· Forward/reverse jog control.
· Emergency stop button.
· Main power switch.
· RS 232 link for remote programming.
· Discrete outputs for user-defined options |
|
|
|
|
|
|
Under-driven AC motor makes it compact and easy to mount |
|
The user-friendly controller can be easily programmed |
|
Strip location can be determined by two independently adjustable guide rolls on feed entrance |
|
Permanently sealed, lubricated bearings reduce maintenance problems caused by dust and dirt contamination |
|
Easily mounts to front, back or either side of a press |
|
Pre-programmed acceleration and deceleration curves eliminate operator input |
|
Dynamic Feeds' proprietary software can be easily modified for special applications |
|
|
|
|
|
|
Standard Pilot Release
The Model DX/EV comes standard with pneumatic, high speed pilot release system precisely controlled by a patented central cylinder. Pressure is controlled by a single regulator for both clamping and pilot release. |
| |
|
|
Pre-Programmed For Quick Set Up
Completely computer-controlled, the DX/EV is pre-programmed to walk the operator through a simple two step start-up process:
1. feed length
2. speed rate
The feed then automatically sets itself up for production. Acceleration
and deceleration curves are pre-programmed for optimum speed and operator ease. |
| |
|
|
Strokes Per Minute vs. Feed Length
|
|
|
|
|
Model
Number |
Material Width |
Material Thickness |
Material Cross Section |
Feed Length |
Feed Accuracy |
| DX/EV 12 |
.197"-4.72" |
.002"-.098" |
.310 sq. " |
.004"-256" |
.002" |
| DX/EV 22 |
.197"-8.66" |
.002"-.098" |
.310 sq. " |
.004"-256" |
.002" |
| DX/EV 112 |
.197"-4.72" |
.004"-.157" |
.620 sq. " |
.004"-256" |
.002" |
| DX/EV 122 |
.197"-8.66" |
.004"-.157" |
.620 sq. " |
.004"-256" |
.002" |
| DX/EV 220 |
.197"-8.66" |
.004"-.24" |
1.395 sq. " |
.004"-256" |
.002" |
| DX/EV 320 |
.197"-12.6" |
.004"-.24" |
1.395 sq. " |
.004"-256" |
.002" |
| DX/EV 420 |
.197"-16.5" |
.004"-.24" |
1.395 sq. " |
.004"-256" |
.002" |
| DX/EV 520 |
.197"-20.5" |
.004"-.24" |
1.395 sq. " |
.004"-256" |
.002" |
|
** Other models and options are available for special applications. |
|
|
|
