FMCMCIIFN
Home
About
Inventory
Lines
Docs
Surplus
Tax
Leasing
Search
Location
Contact

Dreis & Krump
Special Purpose Dies

Special Purpose Punches and Dies

Hemming dies, Goose Neck die punches for channel making, and Offet Bending die sets.

General Purpose 90° Forming Punches and Dies

Commonly used for forming 90° bends. Forming bends greater than 90° is also practical by air bending. The press brake ram is adjusted to limit the depth of punch travel into the die to obtain the desired bend angle.

General Purpose 30° Forming Punches and Dies

Acute Dies are the most universal type of press brake dies. Recommended as a starter set. Make air-form bends from 30° to shallow bends, and also for first operation set in hemming.

Tonnage Requirement Chart

Goose Neck Shaped Forming Punches
These Gooseneck Punches are ideal for channel forming in 2 strokes, or for making special shapes wherea straight 90° punch would interfere. Dimensions show width of face and length of return flange. Any further cutback beyond the center line will increase the length of return flange, but reduces work capacity of the punch.
Goose Neck Punch
Number 6A - 1/4" - 22 Gauge		 Goose Neck Punch
Number 6B - 3/8" - 18 Gauge
Goose Neck Punch
Number 6C- 1/2" - 14 Gauge		 Goose Neck Punch
Number 9A - 3/4" - 10 Gauge
Goose Neck Punch
Number 9B - 1" - 9 Gauge		 Goose Neck Punch
Number 9C - 1 1/4 " - 3/16 Capacity
Goose Neck Punch
Number 7A - 7/16" - 16 Gauge		 Goose Neck Punch
Number 7B - 3/4" - 12 Gauge
Goose Neck Punch
Number 7C - 1" - 10 Gauge
General Purpose Hemming Die Set
Hem is completed in 2 strokes on 18 gauge and lighter mild steel.
Hemming Punch
Number 34 - 18 Gauge		 Hemming Die
Number 35 - 18 Gauge
General Purpose Flattening Dies
Flattening Dies are used to complete a hem or to bend to a given degree of closure a previously formed acute angle. 2 dies are used, both of the same part number.
Flattening Die
Number 16A		 Flattening Die
Number 16B
Flattening Die
Number 16C		 Flattening Die
Number 18A
Flattening Die
Number 18B
Offset Dies
These general purpose Offset Dies form two 90° bends at one stroke. Sizes shown are suitable for mild steel up to 18 gauge. Other metals and heavier gauges of mild steel can be formed depending on size of offset and press brake capacity available. Dimensions shown clearly illustrate the amount of offset from inside to outside of metal thickness.
Offset Die
Number 12 - 1/8"		 Offset Die
Number 12 - 3/16"
Offset Die
Number 12 - 1/4"		 Offset Die
Number 12 - 5/16"
Offset Die
Number 12 - 3/8"		 Offset Die
Number 12 - 1/2"
Offset Die
Number 14 - 5/8"		 Offset Die
Number 14 - 3/4"
Offset Die
Number 14 - 7/8"		 Offset Die
Number 14 - 1"


Major Tax Incentive For New Equipment Orders


Request Literature


Chicago Dreis & Krump | Hydraulic Brakes | Tooling | Shears | Hand Brakes
Leaf Brakes | Notchers | Mechanical Brakes | Mechanical Presses | Parts
Home | About | Inventory | Lines | Docs | Surplus | Tax | Leasing | Search | Location | Contact
Copyright © 2010 Machinery Consultants, Inc., all rights reserved.
1854 Business Center Drive · Duarte, CA 91010
Main Office: (626) 359-1944 · Orange County: (949) 481-6903 · Fax: (626) 359-4055
Terms of Service · Privacy Policy